Division of Mechanical Sciences: Recent submissions
Now showing items 1241-1260 of 1943
-
Experimental Study On The Impact Of Water Drops On Groove-Textured Surfaces
(2014-09-08)The interaction of a liquid drop with a solid surface is being actively studied to understand practically encountered scenarios such as the impact of fuel spray droplets onto the walls of engine combustion chamber, the ... -
A Synergetic Micromechanics Model For Fiber Reinforced Composites
(2014-09-08)Composite materials show heterogeneity at different length scales. hence concurrent multiscale analysis is the only reliable method to analyze them. But unfortunately there is no concurrent multi-scale strategy that is ... -
Modeling And Computation Of Turbulent Nonreacting And Reacting Sprays
(2014-09-05)Numerical modeling of several turbulent nonreacting and reacting spray jets is carried out using a fully stochastic separated flow (FSSF) approach. As is widely used, the carrier-phase is considered in an Eulerian framework, ... -
Lower Bound Limit Analysis Applications For Solving Planar Stability Problems In Geomechanics
(2014-09-04)Limit analysis based upon the theory of plasticity is one of the very useful numerical techniques to determine the failure loads of different civil and mechanical engineering structures for a material following an associated ... -
Micro-Blast Waves
(2014-09-02)The near field blast–wave propagation dynamics has been a subject of intense research in recent past. Since experiments on a large scale are difficult to carry out, focus has been directed towards recreating these blast ... -
Studies On Fatigue Crack Propagation In Cementitious Materials : A Dimensional Analysis Approach
(2014-08-19)Crack propagation in structures when subjected to fatigue loading, follows three different phases namely - short crack growth, stable crack growth and unstable crack growth. Accurate fatigue life prediction demands the ... -
Novel Suspension Mechanisms For A Three Wheeled Mobile Robot Traversing Uneven Terrains Without Slip
(2014-08-12)A wheeled mobile robot (WMR) will move on uneven terrain without slip if the length of the axle connecting two wheels can change or for a fixed length axle the wheels are allowed to tilt in a lateral direction. In this ... -
Kinematic And Dynamic Modeling Of Human Walking
(2014-08-07)Walking comes naturally to us and appears to be simple. However, this is not so and it is known that walking requires high level neural control and muscle coordination. There is no single, unifying theory of bipedal walking. ... -
Collision Avoidance And Coalition Formation Of Multiple Unmanned Aerial Vechicles In High Density Traffic Environments
(2014-08-07)This thesis addresses the problems of collision avoidance and coalition formation of multiple UAVs in high density traffic environments, proposes simple and efficient algorithms as solutions, and discusses their applications ... -
Parametric Analysis Of A Free Piston Stirling Engine For Spacecraft Power Applications With A Radioisotope Heat Source
(2014-07-11)Stirling engines are promising candidates for applications where air breathing engines cannot be used. Self contained engines capable of operating independently of the environment are required to convert thermal energy ... -
Packed Bed Gasification-Combustion In Biomass Based Domestic Stoves And Combustion Systems
(2014-07-04)This thesis constitutes fundamental experimental and computational investigations on gasification and combustion in a packed bed of biomass. Packed bed gasification-combustion in counter-current mode is used in two ... -
Experimental Measurement Of Flame Response To Acoustic Oscillations
(2014-06-20)Acoustic instabilities in a combustion chamber arise due to the coupling of acoustic pressure with in-phase heat-release, and are characterized by large amplitude oscillations of one or more natural modes of combustor. ... -
Wave Propagation In Hyperelastic Waveguides
(2014-06-20)The analysis of wave propagation in hyperelastic waveguides has significant applications in various branches of engineering like Non-Destructive Testing and Evaluation, impact analysis, material characterization and damage ... -
An Extended Integrated Model Of Designing
(2014-06-20)Product success is a major goal of designing and design research. Designing involves developing systems. A system interacts with its environment to satisfy its requirements. Therefore, designing should involve developing ... -
Thermodynamic Analysis And Simulation Of A Solar Thermal Power System
(2014-05-21)Solar energy is a virtually inexhaustible energy resource, and thus, has great potential in helping meet many of our future energy requirements. Current technology used for solar energy conversion, however, is not cost ... -
Development Of Cast Magnesium Alloys With Improved Strength
(2014-05-15)Aim of the present work was to explore the possibility of improving strength of cast Mg by alloying additions, viz., Si and Zn+Al. All the alloys were produced by squeeze casting technique using squeeze pressure of 12MPa ... -
Numerical Methods For Solving The Eigenvalue Problem Involved In The Karhunen-Loeve Decomposition
(2014-05-05)In structural analysis and design it is important to consider the effects of uncertainties in loading and material properties in a rational way. Uncertainty in material properties such as heterogeneity in elastic and mass ... -
Multi-Phase Modeling Of Microporosity And Microstructures During Solidification Of Aluminum Alloys
(2014-04-23)Manufacturing of light-weight materials is associated with several types of casting defects during solidification. Porosity defects are common, especially in aluminum and its alloys, which initiate crack propagation and ... -
Role Of Hydrogen Injection Temperature On The Combustion Instability Of Cryogenic Rocket Engine
(2014-04-16)Physical mechanism for high frequency instability in cryogenic engines at low hydrogen injection temperature has been a subject of debate for long time. Experimental and early developmental studies revealed no instabilities ... -
Integrating Product Model With Assembly Process Model Using Liaisons
(2014-04-09)This thesis addresses the problem of achieving better convergence between different phases (here design and manufacturing) of the product development cycle. The use of liaison has been proposed to better integrate the ...