Mechanical Engineering (ME): Recent submissions
Now showing items 161-180 of 372
-
Design and Development of Capacitive Micromachined Ultrasonic Transducers
(2018-02-22)This thesis presents the design and analysis for development of a Capacitive Micromachined Ultrasonic Transducer (CMUT), a novel sensor and actuator, aimed at replacing the conventional piezoelectric transducers for ... -
Creation of an Orderly Jet and Thrust Generation in Quiescent Fluid from an Oscillating Two-dimensional Flexible Foil
(2018-02-22)In nature, many of the flapping wings and fins in swimming and flying animals have various degrees of flexibility with strong and coupled solid-fluid interactions between the structure and the fluid. In most cases, the ... -
Maintaining Underwater Cassie State for Sustained Drag Reduction in Channel Flow
(2018-02-21)Water droplets tend to bead up on rough or textured hydrophobic surfaces by trapping air on the crevices underneath resulting in “Cassie” state of wetting. When a textured hydrophobic surface is immersed in water, the ... -
Non-Dimensional Kinetoelastic Maps for Nonlinear Behavior of Compliant Suspensions
(2018-02-18)Compliant suspensions are often used in micromechanical devices and precision mechanisms as substitutes for kinematic joints. While their small-displacement behavior is easily captured in simple formulae, large-displacement ... -
Studies on the Design of Novel MEMS Microphones
(2018-02-17)MEMS microphones have been a research topic for the last two and half decades. The state-of-the-art comprises surface mount MEMS microphones in laptops, mobile phones and tablets, etc. The popularity and the commercial ... -
Experimental and Numerical Studies on Spray in Crossflow
(2018-02-06)The phenomenon of spray in crossflow is of relevance in gas turbine combustor development. The current work focuses on spray in crossflow rather than liquid jet in crossflow from the standpoint of enhancing fuel dispersion ... -
Nano Porous Alumina Based Composite Coating for Tribological Applications
(2018-02-06)Anodisation is a surface treatment process, commonly used to form a protective oxide coating on the surface of metals like aluminium. Anodised coatings, being grown out of the base metal have excellent interface strength ... -
Shock Wave-boundary Layer Interaction in Supersonic Flow over Compression Ramp and Forward-Facing Step
(2018-01-12)Shock wave-boundary layer interactions (SWBLIs) have been studied ex-tensively due to their practical importance in the design of high speed ve-hicles. These interactions, especially the ones leading to shock induced ... -
Continuum Modeling Of Adhesive Interaction Based On Interatomic Potentials
(2018-01-12)Adhesion between solid bodies plays a prominent role in a wide variety of situations ranging from tribological applications to dust coagulation initiating the formation of planets. It can be due to various reasons like ... -
Generation, Characterization and Control of Nanoscale Surface Roughness
(2018-01-11)Surface roughness exists at many length scales-from atomic dimensions to meters. At sub-micron scale, the distribution of roughness is largely dependent on the process that generates the surface through the mechanisms of ... -
Micro-Mechanisms Associated with Friction Stir Welding of Aluminum with Titanium
(2018-01-10)Out of the known aerospace metal and alloys, Aluminium (Al) and Titanium (Ti) are important due to their unique combination of properties, such as strength, ductility and corrosion resistance etc. For these reasons, welding ... -
A Design Concept of a Volumetric Solar Receiver for Supercritical CO2 Brayton Cycle
(2018-01-09)Recently, the supercritical carbon dioxide (s-CO2) Brayton cycle has been identified as a promising candidate for solar-thermal energy conversion due to its potentially high thermal efficiency (50%, for turbine inlet ... -
Experimental Study of Flow Past a Circular Cylinder with a Flexible Splitter Plate
(2018-01-04)A circular cylinder is a geometrically simple bluff body that occurs in various practical applications. As with any bluff body, it exhibits large drag forces and a strong fluctuating lift force, both related to the strong ... -
Frequency-Tuning and Dynamic Simulation of Electrostatically Actuated Beams
(2018-01-03)The resonance frequency of electrostatically actuated micromachined beams can be tuned substantially by applying a DC voltage bias, first by decreasing the frequency until the onset of pull-in and then by increasing it by ... -
Generalized Circular and Elliptical Honeycomb Structures/Bundled Tubes : Effective Transverse Elastic Moduli
(2018-01-01)Omnipresence of heterogeneity is conspicuous in all creations of nature. Heterogeneity manifests itself in many forms at different scales, both in time and space. Engineering domain being an exotic fusion of human creativity ... -
Robust Finite Element Strategies for Structures, Acoustics, Electromagnetics and Magneto-hydrodynamics
(2017-12-13)The finite element method (FEM) is a widely-used numerical tool in the fields of structural dynamics, acoustics and electromagnetics. In this work, our goal is to develop robust FEM strategies for solving problems in the ... -
A Numerical Implementation of an Artery Model Using Hybrid Fem
(2017-12-07)The goal of this thesis is to develop a hybrid _nite element formulation to carry out stress analysis of arteries. To the best of our knowledge, a hybrid _nite element impel mentation of the Holzapfel-Ogden artery model ... -
Stall Flutter of a Cascade of Blades at Low Reynolds Number
(2017-12-05)Due to the requirements for high blade loading, modern turbo‐machine blades operate very close to the stall regime. This can lead to flow separation with periodic shedding of vortices, which could lead to self induced ... -
Power Loss Minimization for Drag Reduction and Self-Propulsion using Surface Mass Transpiration
(2017-11-29)The remarkable efficacy with which normal surface mass transpiration (blowing and suction) alters a given base flow to achieve a desired predefined objective has motivated several investigations on drag reduction, ... -
Specification and Verification of Tolerances for Parts with Free-Form Surfaces
(2017-11-27)The need for increased product variety and improved aesthetics require the manufacturing enterprise to reduce time to market and to increase use of free-form surfaces in the form of the product. These changes lead to ...