Browsing Materials Engineering (MatEng) by Advisor "Jayaram, Vikram"
Now showing items 1-20 of 30
-
Comprehensive Investigation of the Mechanical Behavior of Nial-x (X=pt, Pd) Alloys: Effect of Composition, Orientation and Temperature
Gas turbine engines in the turbine section operate at temperatures exceeding 1300°C, which can cause high-temperature oxidation and reduce the lifespan of turbine blades. To counter this, thermal barrier coating (TBC) ... -
Densification, Oxidation, Mechanical And Thermal Behaviour Of Zirconium Diboride (ZrB2) And Zirconium Diboride - Silicon Carbide (ZrB2-Sic) Composites
(2016-11-23)Sharp leading edges and nose caps on hypersonic vehicles, re-entry vehicles and reusable launch vehicles are items of current research interest for enhanced aerodynamic performance and maneuverability. The unique combination ... -
Design, Fabrication and Application of In situ Total Internal Reflection (TIR) Raman Tribometer For the Chemical Analysis of Tribological Systems
In conventional tribological experiments that study friction and wear behavior of materials, the contact interface is hidden by the contacting bodies. The physical or chemical phenomena taking place at the interface must ... -
Dry Sliding Wear of Saffil Short Fibre Reinforced AZ91D Mg Alloy Composite
(2018-03-01)Magnesium alloys have emerged as a promising material for light-weighting due to their potential for higher weight saving compared with advanced high-strength steel, aluminium alloys and glass fibre reinforced polymer ... -
Effect of Humidity and Temperature on Wear of TiN and TiAIN Coatings
(2018-05-30)When loss of material due to sliding of two solids is promoted/prevented, in the presence of chemically reacting liquid or gas, tribochemical wear is said to occur. Tribochemical wear, in which corrosive media promotes ... -
Effect of Sintering on Microstructure and Mechanical Properties of Air Plasma Sprayed 7 wt.% Y2O3 Stabilized ZrO2
Air plasma sprayed (APS) 7 wt.% Y2O3 stabilized ZrO2 (7YSZ) coating is conventionally used for thermal insulations (in form of thermal barrier coating, TBC) in various hotter sections of land-based gas turbine engines and ... -
Evaluation of Power-Law Creep in Bending
Materials for engineering components operating at high temperatures during their service like rockets, aero-turbines, automobile engines, nuclear power plants, steam power plants and micro-electronics are often designed ... -
Extraction of Bond Coat Mechanical Properties using High- Temperature Digital Image Correlation
Gas turbine engines used in aircraft or power generation widely use nickel-based superalloys in their hot sections such as combustion chambers, turbine blades, etc. These components in the hot section use thermal barrier ... -
Extraction of Creep Parameters from Indentation Creep Experiment: An Artificial Neural Network- Based Approach
Conventional methods for extracting creep properties require conducting several uniaxial tests at different loads, which consumes an intensive amount of material and time. Indentation may minimize the material volume ... -
Extraction of Equivalent Uniaxial Plastic and Viscoplastic Behavior from Bending Using a Mechanistic Approach
The present work is aimed at the extraction of material’s yield and creep parameters using cantilevers by conducting constant deflection rate and constant load tests respectively. Under the assumption of Euler-Bernoulli’s ... -
High-Throughput Bending Tests for Investigating Creep Behavior Affected by Structural and Microstructural Inhomogeneities
The bending of cantilevers is an alternate technique for the extraction of power-law creep parameters of materials. It has been shown earlier that in homogeneous systems showing tension-compression symmetry, digital image ... -
Influence of Surface Topography and Tribosystem on Reciprocating Friction in Sparsely Lubricated Contacts
Surface texturing to achieve reduced sliding friction has been a widely studied topic, as seen in contemporary literature. Laser surface texturing, grinding and ion beam milling are popular techniques accepted by researchers ... -
Investigations On The Properties Of TiN, NbN Thin Films And Multilayers By Reactive Pulsed Laser Deposition
(2013-10-21)Two technologies, namely Laser Technology and Surface Modification Technology, have made rapid strides in the last few decades. The lasers have evolved from a simple laboratory curiosity to a matured industrial tool and ... -
Kinetics Of Pressureless Infiltration Of Al-Mg Alloys Into Al2O3 Preforms : A Non-Uniform Capillary Model
(2009-03-06)Al-Mg alloys spontaneously infiltrate into porous ceramic preform in a nitrogenous atmosphere above 750 °C with Mg either pre-alloyed or introduced at the interface to initiate the process. The governing process variables ... -
Mechanism and Modeling of Contact Damage in ZrN-Zr and TiAIN-TiN Multilayer Hard Coatings
(2018-02-23)With the amalgamation of hard coating in cutting tools industries for three decades now, a stage with proven performance has been reached. Today, nearly 40% of all cutting tools used in machining applications are sheltered ... -
Micro-scale Fracture Testing of Graded (Pt,Ni)Al Bond Coats
(2018-04-16)PtNiAl bond coats are diffusion aluminide coatings deposited on superalloy based turbine blades for oxidation resistance and improved adhesion between the substrate and the YSZ thermal barrier coating on top. They are ... -
Microstructural Developments and Mechanical Properties of Electroless Ni-B Coating
(2018-04-24)Phase transformation behavior, micro structural development, mechanical and tribological properties of electroless Ni-B coating was characterized using different characterization techniques. As deposited electroless Ni-B ...